One 45 minute treatment is $135
Buy 3 for $300
One 45 minute treatment is $135
Buy 3 for $300
Salon sanitation is imperative in all salon services. But the one service people worry about the most is having a pedicure. We have all heard horror stories from friends or read about one online. A terrible experience that started with a little voice in their head that told them to turn and leave. But they didn’t and in retrospect, they should have listened to their instinct.
You should always make sure the salon you choose to have your pedicure in follows proper sanitation and sterilization guides set by the State of Michigan. Don’t be afraid to ask how often they clean their tub and what germicide they use to do it. You should also ask if the tub has pipes or tubes the water is circulated through to create the bubbles. These tubs have a much greater risk of bacteria being stored in them and should be avoided. If it isn’t avoidable make sure they run a sterilization agent through the pipes at least once a week.
The goal from our salon’s perspective is 100% patron protection and to guarantee there is no transfer of any communicable virus or bacteria during the pedicure service. Here at Voila Salon & Spa we want you to know we guarantee our standards are above and beyond Michigan’s requirements. (Which are placing washed equipment in a container holding a chemical sanitizing agent. Acceptable agents are those registered for use in interstate commerce by the USDA. Sharp edged tools mush be wiped with a 70% alcohol solution.) We insure that all implements are either single use or sterilized in between every client, not just sanitized. We use 99% alcohol on surfaces and Citricide II to clean the tub in between each client. This chemical sterilizer kills all bacteria and even kills the AIDS virus. Our pedicure tub is pipeless so there is no risk of bacteria being trapped anywhere in the equipment.
So with all this information we hope you know your health and safety is just as important to us as a beautiful pedicure experience. And we hope to see you and your friends soon. Voila Salon & Spa, 151 Keveling Drive, Saline, MI (734) 944-9363.
It is always good to remind people of terms and definitions commonly used in the beauty industry. These definitions are from the Centers for Disease Control and Prevention (CDC).
Sanitation – to wash with soap and water to remove dirt and debris and to reduce the levels of microorganisms to a safe, acceptable level. Before implements or equipment can be disinfected, they must first be sanitized.
Disinfection – the use of a chemical procedure that eliminates virtually all recognized pathogenic microorganisms but not necessarily all microbial forms. (Microorganisms are living organisms, good and bad, that are invisible to the naked eye.) All implements and equipment used on clients must be disinfected before use.
Sterilization – the use of a physical or chemical procedure to destroy all microbial life, including highly resistant bacterial endospores. (Endospores are thick walled bodies formed within the vegetative cells of certain bacteria. They are able to withstand adverse environmental conditions for prolonged periods.)
How to Make Wine/Letter Wedding Box DIY
Wood Supplies Needed:
Kreg Jig pocket hole device
Framing Saw or Miter Saw
Benzomatic Blow Torch
3/4″ wood drill bit
1″ Finishing nails
1 1/4″ wood screws
weathered grey stain
clear satin polyurethane
lock and hasp
2- 14.5″ (1×8) front and back
2- 11″ (1×8) sides
4-8.5″ (2×2) legs
2-14.5″ (1×2) bottom front/back brace
2-11″ (1×2) bottom side braces
1- 12 3/8″ (1×8) divider
4- 5 3/4″ x ripped strips divider holder
1- 4″ (1×2) wine bottle top holder
1- 10″ (1×2) wine bottle bottom holder
1- 16″x12″ plywood bottom
4- 17.5″ (1×4) top slats
2-10″ (1×2) top slat brackets
2-14.5″ plywood straps top
2-7 7/8″ plywood straps front
2- 3/4″ plywood straps frond edge
(sand all your cut pieces before assembling them)
Step 1: Assemble Box Body
Tools needed: Kreg Jig, clamps, drill, 4- 8.5″ (2×2), 2- 14.5″ (1×8), 2- 11″ (1×8), 16 1 1/4″ screws, square, sander
Step 2: Assemble Box Body
Tools needed: Hammer, 1″ finish nails, 2-14.5″ (1×2), 2- 11″ (1×2), square
Step 3: Attach the Bottom of the Box
Tools needed: 16″x12″ plywood, brad nails, hammer, jig saw
Step 4: Assemble Box Top
Tools needed: 4- 17 1/2″ (1×4) slats, 2- 10″ (1×2) brace boards, 16- 1 1/4″ screws, square, sander, drill, hinges
Step 5: Add Straps to Box Top
Tools needed: Wood glue, brad nails, 2- 14 1/4″ ripped straps
Step 6: Customize Aging and Stain
Tools needed: blow torch, stain color of your choice
Step 7: Bottle Neck and Bottom Holder
Tools needed: 3/4″ Wood drill bit, piece of wood for bottle neck holder, jig saw, clamps, felt, scissors, Elmer’s glue
Step 8: Attach Bottle Holder
Tools needed: An assistant and brad nails, finish nail, hammer
Step 9: Attach Divider Piece
Tools needed: Brad nails, hammer, small ripped strips, divider piece
Step 10: Attach the Handles and Hasp
Tools needed: Handles, Hasp, screws, drill, square, level, small clamp, small drill bit, measuring tape
Step 11: Attach safety strap
Tools needed: Upholstery tacks, leather rope
Step 12: Time to Personalize!
Print out of name, pencil, paint brush, paint
Previous 1 2 3 4